Industrial 4-port Coax + 2-port 10/100/1000T + 2-port 100/1000X SFP Long Reach PoE over Coaxial Managed Switch – LRP-422CST

PLANET Long Reach PoE Solution enables all enterprises and network service providers to set up an IP infrastructure in a remote location where 802.3af/at PoE compliant powered devices can receive both data and power via PLANET switches, and PLANET LRP extenders and injectors over a long distance but not limited to the normal 100 meters.

Specifications
Ethernet Interfaces:
Copper
• 2 x 10/100/1000BASE-T RJ45
• Auto-negotiation/Auto-MDI/MDI-X

Fiber Optic
• 2 x 100/1000BASE-X SFP slot
• Supports 100/1000Mbps dual mode and DDM

Jumbo Frame
• 10Kbytes with GE1 to GE4

Long Reach PoE Interfaces:
Connectivity
• 4 x BNC female connectors
• Long Reach PoE over coaxial PSE (Power Source Equipment)
　 – BNC center pole : DC+/Hi
　 – BNC shield : DC -/Lo

Power Output
• Per port 48~56V DC, 36 watts (max.)

Total Power Budget
• 150 watts (max.)

Cabling
• Coaxial cable: 75 ohm
• RG-6/U cable (Recommended)

Maximum Distance
• Max. 200m with PoE+ output (1,640ft.)
• Max. 400m with PoE output (2,624ft.)
• Max. 1200m without PoE output (3,937ft.)

Long Reach Ethernet Standard
• IEEE 1901

Modulation Type
• Wavelet-OFDM

Security
• 128-bit AES encryption

Frequency Band
• 2 ~ 28MHz

Multiple Nodes
• Up to 4 LRP extenders within 1km RG-6/U coaxial cable*

* The actual extender nodes vary on the quality of the copper wire and environmental factors.

LRP Compatibility
• LRP-101CE: 1-Port 10/100TX PoE PSE + 1-Port Coax Long Reach PoE Extender

Console: 1 x RS232-to-RJ45 serial port (115200, 8, N, 1)

Switch Architecture: Store-and-Forward

Switch Fabric: 8.8Gbps/non-blocking

Address Table: 8K entries

Shared Data Buffer: 4.1 megabits

Flow Control:
IEEE 802.3x pause frame for full-duplex
Back pressure for half-duplex

Reset Button:
< 5 sec: System reboot > 5 sec: Factory default

EST Protection: 6KV DC

ESD Protection: 6KV DC

Enclosure: IP30 aluminum case

Installation: DIN-rail kit and wall-mount kit

Connector:
Removable 6-pin terminal block for power input
Pin 1/2 for Power 1; Pin 3/4 for fault alarm; Pin 5/6 for Power 2

Alarm: One relay output for power failure. Alarm Relay current carry ability: 1A @ 24V AC

LED:
System:
Power 1 (Green)
Power 2 (Green)
Fault Alarm (Red)
Per LRP Port:
LNK/ACT (Green)
PoE In-use (Orange)
Per Gigabit Port:
LNK/ACT (Green)
1000 (Orange)

Dimensions (W x D x H): 72 x 107 x 152 mm

Weight: 1,150g

Power Requirements: 48 to 56V DC

Power Consumption:
9.5 watts/32.42 BTU (System on)
165 watts/563.0 BTU (Full loading)

Operating:
Temperature: -20 ~ 75 degrees C
Relative Humidity: 5 ~ 95% (non-condensing)

Storage:
Temperature: -40 ~ 85 degrees C
Relative Humidity: 5 ~ 95% (non-condensing)